Categories FAQ

How do i reset my rain bird sst sprinkler system?

How do I reset my Rain Bird Sprinkler System?

How can I clear all the programming and reset my Rain Bird ESP-Me sprinkler timer back to the factory default settings? Turn the dial to Seasonal Adjust. Press and hold the left and right arrow buttons at the same time for at least 3 seconds. Until you see the word “CLEARED” on the screen. Turn the dial back to AUTO RUN.

How do you reprogram a Rainbird sprinkler system?

Rotate the dial to the “Watering start time” position and press the “+” or “-” keys to reprogram the time of day the watering cycle begins. Each zone will water in sequence starting at the time indicated. Programming multiple start times initiates the entire watering cycle again on the same day.

How do I reset my sprinkler system?

How to Reset a Sprinkler System Turn the control dial to the “off” position. Press the “next” button to access the clear-memory feature. Press and hold the “off” button until the display stops blinking. Turn the control dial to the “run” position. Press and hold down the “minus” arrow and “prog” buttons simultaneously.

You might be interested:  Comment Choisir Une Museliere Pour Chien?

Why does my Rainbird sprinkler system run twice?

A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.

How long should I run each sprinkler zone?

As a general rule rotor heads should run twice as long as spray heads. When conditions become dry and the need for spring watering begins, set rotor zones to run 30 minutes in each zone and spray heads for 15 minutes.

Why does my irrigation system finish watering and then start again?

If a station does not have a run time set, it will be skipped, and the next consecutive station with a run time in the program will start watering. Set up your watering schedule — the specific day or days the program runs.

Why does my sprinkler system keep running?

More often than not, there will be a valve that is stuck in the “open” position on the pressurized system. When the valve remains open, water continues to run down the line, which causes your sprinkler to continuously run even when the timer is in the “off” position.

Why do my sprinklers turn on twice?

A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time.

You might be interested:  Readers ask: Why did they shut down flappy bird?

Why does my sprinkler system not work?

Backflow Device Valves If your sprinkler system won’t turn on or if you have low water pressure, this could be caused by the valves not being turned on all the way. Just locate the valves and make sure they are both turned on (you should have 2 valves, one located on the horizontal pipes and one for the vertical ones).

Why is my Rainbird not working?

Check that the wires are secure on the timer, and check the wiring in your valve box. If the wiring is fine in both places, then you may have a break in the wires in between. If that is not the issue, check to make sure your backflow device or all water supply valves are open.

How often should I water my lawn with sprinkler system in Texas?

Augustine grass, the time of year will determine how long you need to water. For the first three and last three months of the year, five hours every 10 days will normally do the trick. During the middle of the year, running your sprinkler for about two hours every other day will typically keep your grass healthy.

What does seasonal adjustment mean on sprinkler system?

Seasonal adjustment is a feature on most irrigation controllers that reduces or increases run times for all zones based on a percentage of the programmed time (Example: 10 minute run time at 50% would instead run 5 minutes).

How do I turn off my Rainbird sprinkler system for winter?

How Do I “Winterize” My Irrigation System Insulate your assets: Shut off the water supply to the irrigation system. Stay in control: If you have an automatic system then you will need to ” shut down” the controller ( timer ). Drain the pipes: Protect valves and backflow preventers:

1 звезда2 звезды3 звезды4 звезды5 звезд (нет голосов)

Leave a Reply

Your email address will not be published. Required fields are marked *